Use this bar to show information about your cookie policy.
Description
RAM Universal SMALL Tab-Tite Holder for 7" Screen Tablets including the Samsung Galaxy, Dell Streak 7 & BlackBerry PlayBook
Now that you've got the right Tab for the job, you are going to need the right mounting system. Get the most out of your tablet with the Universal RAM Tab-Tite cradle. With 3 sets of interchangeable cup ends, ranging from different sizes and features, you can fit the holder to your tablet for a near custom fit. This spring loaded design makes it easy to load and unload your tablet, along with keeping it secure while on the go. Cup ends are designed to optimize the functionality of your tablet, allowing access to audio jacks, USB, power, and other ports, your tablet can be used just as it was intended. Perfect for stationary or on the go applications, this new RAM product is just what you need to get the most out of your mobile device.
The Tab-Tite is compatible with the following tablets WITH OR WITHOUT SKINS, SLEEVES OR CASES:
Archos 7
Asus EEE Pad Memo
Barnes & Noble NOOKcolor
BlackBerry PlayBook
Dell Streak 7
HTC Flyer
Samsung Galaxy
Included With Purchase:
(1) Spring loaded back plate
(2) Support cups for thin tablets with no skins
(2) Support cups for thin tablets with thin or no skins
(2) Support cups for thick tablets with cases
Mounting hardware
The Tab-Tite cradle is compatible with any tablet that will fit the dimensions listed below. It is important to verify the dimensions of your tablet with a case/sleeve/skin when determining the overall size.
Cradle Dimensions:
Height: 7.3" minimum to 9.62" maximum
Width: Maximum width to 5.31"
Depth: 1.06" maximum
Cradle Dimensions:
Height: 6.80" minimum to 9" maximum
Width: Maximum width to 5.31"
Depth: 0.125" minimum to 0.56" maximum
Cradle Dimensions:
Height: 5" minimum to 9.1" maximum
Width: Maximum width to 4.70"
Depth: 0.125" minimum to 0.44" maximum
Features:
1. Support cups contain open slots to accommodate for tablets of various sizes
2. Back plate can support various size support cups
3. Spring loaded tension provides secure support for your tablet
4. Spring loaded cradle allows for quick release of your tablet
5. Full access to all ports
Material: High Strength Composite
Note: The "U" in the part number reflects product packaged in poly bag. Diamond base adapter not included with purchase.
No issues with install and regulator installation.
At first has some rpm reading issue but it was easily fixed by tweaking min duty setting thanks to the support team at yacht rigger.
Installed with an APS alternator.
ARCO Zeus Alternator Regulator- Standard
Tom in Oxford
Lugs .... but more
While the review is for lugs, its actually for a lot more than that. I upgraded from AMGs to new lithium batteries. I bought these 4/0 lugs but also the 4/0 cables, fuses, cable shrink wrap and more. Basically everything I needed for the project. A huge shout out to the Yacht Rigger as being a DYI'er there were bits and pieces I needed last minute that got shipped right away and then a few items that I swapped out. They made this super easy.
Ancor 90 Tinned Copper Lug #4/0 - 3/8" - 2-Piece
Tom in Oxford
Arco Zeus alternator regulator
After a lot of research, bought two of these units to go along with new Balmer XT-CR-170 alternators. Installation was a challenge but only due to having to run wires from one side of boat to the other but the support from Yacht Rigger electrical department was stellar. I had a couple of calls with Mike and he walked me through setup and configuration.
ARCO Zeus Alternator Regulator- Extended
Adam Green
Nice product for sealing cable routes on my boat
Using this for a Starlink install. Looks to be easy to use and effective in keeping water out of the hole for the cable.
Super high quality products! Easy to install with the easy-to-follow instructions and expert guidance from The Yacht Rigger. (Be sure to turn the shore power off and unplug the cord!)
