Use this bar to show information about your cookie policy.
Description
RAM Universal Finger Grip Holder Brake/Clutch Reservoir Mount Part #: RAM-B-184-UN4U
The base consists of a 1" diameter rubber ball, hardware for mounting to both brake/clutch reservoirs and rails that are 0.5" to 1.25" in diameter. The mounting hardware for brake/clutch reservoirs include both standard and metric mounting bolts. Multiple pivot points, rubber ball and socket technology allows for almost infinite adjustment and perfect viewing angles. High quality materials insure your device is safe, secure, and within easy reach.
The RAM Composite Universal Finger Grip Holder is designed to hold a large amount of cell phones and electronic devices. The holder comes with (3 sets) of four flexible rubber coated fingers placed along sides to grip your device. The fingers open by squeezing the ends to open the small finger arms. The bottom of the holder includes a back plate that adds support to the device being held by the mount.
This mount is designed to hold the following devices: Cell Phones 2-Way Radios GPS Devices
Height Dimensions: Minimum with Top and Bottom Plates: 5.25" Maximum with Top and Bottom Plates: 6.0" The top and bottom plates can be removed for larger devices.
Spine Plate Dimensions: 2.5W x 5.0H"
Using Short Arm Side Clamps: Maximum Depth: 0.75" Minimum Width: 1.25" Maximum Width: 3.0"
Using Medium Arm Side Clamps: Maximum Depth: 1.25" Minimum Width: 1.5" Maximum Width: 3.5"
Using Long Arm Side Clamps: Maximum Depth: 1.6" Minimum Width: 2.25" Maximum Width: 3.5"
Included with Purchase: (1 qty) Universal Finger Grip holder (1 qty) Base/ball adaptor (attaches directly to cradle) (1 qty) Standard size double socket arm (1 qty) Mounting base (mounts to either brake/clutch reservoir or rail/handlebar) Hardware for mounting to either brake/clutch reservoir or rail/handlebar
Material: High Strength Composite and Powder Coated Marine Grade Aluminum
Ball Size: 1" Rubber Ball "B" Size
Note: *The RAM-B-174-UN4U can mount to both the brake/clutch reservoir or any round rail that is 0.5" to 1.25" in diameter.The "U" in the part number reflects product packaged in poly bag. To see if the RAM-B-174-UN4U base will mount to your motorcycle, check the hole spacing of the base against your clutch/brake reservoir. The holes centers have a minimum width of 0.94" and a maximum of 1.58".
No issues with install and regulator installation.
At first has some rpm reading issue but it was easily fixed by tweaking min duty setting thanks to the support team at yacht rigger.
Installed with an APS alternator.
ARCO Zeus Alternator Regulator- Standard
Tom in Oxford
Lugs .... but more
While the review is for lugs, its actually for a lot more than that. I upgraded from AMGs to new lithium batteries. I bought these 4/0 lugs but also the 4/0 cables, fuses, cable shrink wrap and more. Basically everything I needed for the project. A huge shout out to the Yacht Rigger as being a DYI'er there were bits and pieces I needed last minute that got shipped right away and then a few items that I swapped out. They made this super easy.
Ancor 90 Tinned Copper Lug #4/0 - 3/8" - 2-Piece
Tom in Oxford
Arco Zeus alternator regulator
After a lot of research, bought two of these units to go along with new Balmer XT-CR-170 alternators. Installation was a challenge but only due to having to run wires from one side of boat to the other but the support from Yacht Rigger electrical department was stellar. I had a couple of calls with Mike and he walked me through setup and configuration.
ARCO Zeus Alternator Regulator- Extended
Adam Green
Nice product for sealing cable routes on my boat
Using this for a Starlink install. Looks to be easy to use and effective in keeping water out of the hole for the cable.
Super high quality products! Easy to install with the easy-to-follow instructions and expert guidance from The Yacht Rigger. (Be sure to turn the shore power off and unplug the cord!)
